共找到 150 條與 側向速度 相關的標準，共 10 頁
NASM17988, "PIN, QUICK RELEASE, SELF-RETAINING, POSITIVE LOCKING, DOUBLE ACTING, "T" HANDLE, was adopted on 20 MARCH 2000 for use by the Department
Pin, quick release, self-retaining, positive locking, double acting,"T" handle
? ??? ??? ???? ?? ??? ???? ? ???? ???? ?? ???(?? ?
Wind direction & indicating equipment for marine use-Synchro type
本文件規定了自動氣象站傳感器更換的一般要求，氣壓、空氣溫度和濕度、風向和風速、地溫傳感器的更換和驗收、作業事宜的記錄與存檔要求。本文件適用于自動氣象站氣壓、空氣溫度和濕度、風向和風速、地溫傳感器的更換工作
Automatic weather station sensor replacement specification air pressure, air temperature and humidity, wind direction and speed, ground temperature
NASMl7986, "PIN, QUICK RELEASE, SELF-RETAINING, POSITIVE LOCKING, SINGLE ACTING "L" HANDLE", was adopted on 30 NOVEMBER 1998 for use
Pin, quick release, self-retaining, positive locking, single acting,"L" handle
? ??? 1974? ??? ??????? ?? ????(SOLAS)? ?5? ?? 5? ?? ?????? ???? ??? ??? ?? ? ??? ?? ??? ???? ??? ???? ???(??“???? ???”? ??.)? ??, ??, ??, ??? ????? ?
Marine wind vane and anemometers
Diese ?NORM beschreibt die kontinuierliche Messung des Windes nahe der Erdoberfl?che [siehe Abschnitt 6 (2) und (3
Meteorological measurements for purposes of air pollution control - Measurement of wind (direction and velocity)
NASM17989, "PIN, QUICK, RELEASE, SELF-RETAINING, POSITIVE LOCKING, DOUBLE ACTING "L" HANDLE", was adopted on 21 JUNE 1999 for use by the Departmento
Pin, quick release, self-retaining, positive locking, double acting,"L" handle
本標準規定了旋轉式風向風速傳感器（包括旋轉式風向傳感器和旋轉式風速傳感器，以下簡稱傳感器）的基本要求、技術要求、試驗方法、檢驗規則及標志、包裝、運輸與貯存、質量承諾等內容。 本標準適用于風力發電機組用旋轉式風向風速傳感器，其他使用環境下的風向風速傳感器可參照執行
Revolving wind direction and wind speed sensor
The practice and innovation of quality development--the leap from "Shenzhen speed" to "Shenzhen quality"
DETECTOR, WIND DIRECTION, SPEED, AND TEMPERATURE, FIRE AND FLIGHT AIR DATA SUBSYSTEM, HELICOPTER ARMAMENT: M143
Specifies a method for the design, conduct, assessment and certification of office shorthand speed tests of 60 wpm or greater. Includes a list of 500
Shorthand speed tests
Radial type permanent magnet mechanical speed regulator
1.1 This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high
Test Method for Bursting Strength of Textiles-Constant-Rate-of-Traverse (CRT) Ball Burst Test
This part of ISO 7176 specifies test methods for determining the maximum speed, acceleration and deceleration of electrically powered wheelchairs
Wheelchairs - Determination of maximum speed, acceleration and deceleration of electric wheelchairs
Cross References: ISO 6440 ISO 7176-11 ISO 7176-15 ISO 7176-22
Wheelchairs-Determination of maximum speed, acceleration and deceleration of electric wheelchairs
