共找到 150 條與 壓力額定值 相關的標準，共 10 頁
本標準規定了螺栓連接閥蓋鋼制旋啟式止回閥(簡稱為“止回閥”)的結構形式、技術要求、材料、試驗方法和檢驗規則、標志、防腐、涂漆、包裝和儲運等。 本標準適用于螺栓連接閥蓋的法蘭連接或焊接的鋼制旋啟式止回閥。其參數為：公稱壓力PNl6～PN420，公稱尺寸DN50～DN600，使用溫度
Steel swing check valve for petroleum,petrochemical and allied industries
本標準規定在短時間內（0到2.5s）以高速度定量之合成血液對醫用面罩穿透阻力之試驗法。以目視檢測合成血液是否穿透判定醫用面罩之合格與否
Method of test for resistance of medical face masks to penetration by synthetic blood (horizontal projection of fixed volume at a known velocity)
本標準規定了空氣分離設備用往復式低溫液體泵的技術要求，試驗方法和檢驗規則，標志、包裝、運輸與貯存。 本標準適用于輸送介質為液氧、液氮、液氬，排出壓力不高于35MPa的泵。 注：本標準中壓力除注明者外均為表壓
Specifications for reciprocating cryogenic liquid pumps
The following table shows the recommended allowable ratings for propeller shaft ends for low horsepower engines. Ratings are based on the formula
Propeller Shaft Torque Ratings
本標準適用于 CNS 3376 一般用電機具防爆構造試驗法
Method Test for Electrical Apparatus for Use in Explosive Gas Atmospheres
本標準規定了液壓元件和液壓輔件型號的編制方法。 本標準適用于以液壓油或性能相當?shù)钠渌ぷ鹘橘|的一般工業用途的液壓元件和液壓輔件
Hydraulic fluid power.Method for coding the typeof hydrauIic components
Rating of Truck Power Take-Offs
The power take-offs included in this SAE Standard are those which are driven from the transmission, auxiliary transmission, or transfer case
RATING OF TRUCK POWER TAKE-OFFS
Rating of Truck Power Take-Offs
Driving force material octane number determination
GB／T l4041的本部分規定了檢驗液壓濾芯與指定液體相容性的方法，用于驗證濾芯經高溫或低溫條件下的指定系統工作液體浸泡后，維持破裂額定值的能力。 濾芯的材料不包括濾芯中（上）安裝的密封件。 本部分適用于液壓傳動系統用濾芯
Hydraulic fluid power Filter elements Part 2 : Verification of material compatibility with fluids
This standard describes the recommended proof testing of pressure regulators for operation at or below the manufacturer's rated pressure. The purpose
Standard for Proof of Pressure Ratings for Pressure Regulators
1. SCOPE 1.1 This standard describes the recommended proof testing of pressure regulators for operation at or below the manufacturer's rated
Standard for Proof of Pressure Ratings for Pressure Regulators
General specification for hydraulic filters
This document provides quantity definitions for designing and using instrumentation for the measurement of electric power quantities under sinusoidal
Draft Standard Definitions for the Measurement of Electric Power Quantities under Sinusoidal, Nonsinusoidal, Balanced, or Unbalanced Conditions
