共找到 150 條與 手持式XRF光譜儀 相關的標準，共 10 頁
本標準規定了手持式液壓鉗的術語和定義、型號與基本參數、技術要求，檢驗方法、檢驗規則、標志、包裝、運輸和貯存。 本標準適用于手持式液壓鉗（以下簡稱產品
Hand-held hydraulic clamps
Schválení normy ST SEV 1605-79 doporu?ilo federální ministerstvo v?eobecného strojírenství Zpracovatel: Továrny strojírenské techniky, koncernov? V
Hand-held Motor-operated Drills
本文件規定了手持式電烙鐵的術語和定義、基本參數、基本要求、技術要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存和質量承諾。 本文件適用于單相器具額定電壓不大于250 V，額定輸入功率不大于500 W的手持式電烙鐵（以下簡稱電烙鐵）。 本文件不適用于含鋰電池的電烙鐵
Hand-held electric soldering irons
FUEL CANS FOR HANDY TYPE
本標準規定了手持式鑿巖機的型式與基本參數、技術要求、檢驗方法、檢驗規則和標志、包裝、運輸與貯存。 本標準適用于以壓縮空氣為動力的手持式鑿巖機（以下簡稱產品
Hand-held rock drills
本附錄規定了手持式電吹風在開展下表中標志認證時所需增加的技術要求和檢驗方法。A.2 技術要求和檢驗方法 E 見下表。認證標志 M A 國家 D 表A.1 一帶一路沿線主要國家認證及技術差異性要求
Hand-held hairdryer
本標準規定了手持式液壓剪的術語和定義、型式與基本參數、技術要求、檢驗方法、檢驗規則、標志、包裝、運輸和貯存。 本標準適用于手持式液壓剪（以下簡稱產品
Hand-held hydraulic shears
To be read in conjunction with BS EN 60745-1:2003 Cross References: EN 60745-2-3:2007 EN 50144-2-3:2002 EN 60745-1:2003 IEC 60745-2-3:2006 98
Hand-held motor-operated electric tools. Safety-Particular requirements for sanders and polishers other than disk type
Establishes a uniform, repeatable procedure or standard method for measuring specified performance characteristics of household electric irons
Household Electric Irons
Handheld rock drill
This document specifies requirements and test methods common to all non-hinged hand instruments used in dentistry, including materials, hardness
Dentistry. General requirements of hand instruments. Non-hinged hand instruments
ENGLISH This International Standard deals with the safety of electric motor-operated or magnetically driven: – hand-held tools
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety Part 2-3: Particular requirements for hand-held grinders, disc-type polishers and disc-type sanders
GB/T 22665的本部分規定了對手持式砂輪機、拋光機和盤式砂光機在三個正交軸上測量手傳振動的一般方法，以中心頻率為8Hz~1000Hz的倍頻程測量。 本部分適用于按頻率計權振動加速度評價手傳振動的方法，未規定振動限值。 在工作場所條件下的人體接觸手傳振動的評估可按ISO 5349-1和ISO
Measurement of vibrations at the handle of hand-held electric tools.Part 3:Grinders,polishers and disk-type sanders
AS/NZS 62841.2.3:2021 will supersede AS/NZS 60745.2.3:2011 on 25 June 2024. AS/NZS 62841.2.3:2021 applies to hand-held grinders, disc-type polishers
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2.3: Particular requirements for hand-held grinders, disc-type polishers and disc-type sanders
AS/NZS 62841.2.3:2021 will supersede AS/NZS 60745.2.3:2011 on 25 June 2024. AS/NZS 62841.2.3:2021 applies to hand-held grinders, disc-type polishers
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2.3: Particular requirements for hand-held grinders, disc-type polishers and disc-type sanders
