共找到 63 條與 數據采集率 相關的標準，共 5 頁
1 Scope This part of ISO/IEC 14443 specifies the characteristics of the fields to be provided for power and bidirectional communication
Identification Cards - Contactless Integrated Circuit(s) Cards - Proximity Cards - Part 2: Radio Frequency Power and Signal Interface (Adopted ISO/IEC 14443-2:2010, second edition, 2010-09-01)
1 Scope This part of ISO/IEC 14443 specifies the characteristics of the fields to be provided for power and bi-directional communication
Identification Cards - Contactless Integrated Circuit(s) Cards - Proximity Cards - Part 2: Radio Frequency Power and Signal Interface (Adopted ISO/IEC 14443-2:2001, first edition, 2001-07-01)
In this Recommendation, the expression "Administration" is used for conciseness to indicate both a telecommunication administration and a recognized
Determination of Accounting Rate Shares and Collection Charges in Telex Relations between Countries in Africa - Charging and Accounting in International Telecommunication Services-Study Group 3; 13 pp
Labor protection - Laboratory methods for the collection of hazardous fumes and gases during welding and allied processes - Part 4: Determination of emission rates other than ozone
This part of ISO 15011 defines a laboratory method for measuring the emission rate of fume from arc welding. It also defines a method of collecting
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Determination of fume emission rate during arc welding and collection of fume for analysis
Health and safety in welding and allied processes - Requirements, testing and marking of equipment for air filtration - Determination of the minimum air volume flow rate of captor hoods and nozzles
ETSI TS 103 863 V1.1.1 (2023-01)-2023 海上移動寬帶通信鏈路 采用集成波束形成相控陣天線、工作頻率范圍為 5 GHz 至 8 GHz 的無線電發射機和接收機
本文件規定了工作在5 GHz至8 GHz頻率范圍內的無線電發射機和接收機的技術特性和測量方法，不包括5 862 MHz和5 890 MHz頻率，用于船舶之間以及船舶與陸地站之間的寬帶通信鏈路。本文件旨在提供在考慮使用許可或其他權限時可能有用的參數。注：在5 862 MHz和5 890 MHz頻率上的
Maritime mobile broadband communication links; Radio transmitters and receivers employing integrated beamforming phased array antennas operating in the 5 GHz to 8 GHz frequency range
This document defines a set of environmental performance evaluation (EPE) data classes, including their properties. It is applicable
Automation systems and integration — Evaluating energy efficiency and other factors of manufacturing systems that influence the environment — Part 5: Environmental performance evaluation data (ISO 20140-5:2024, IDT)
Health and safety in welding and allied processes - Requirements, testing and marking of equipment for air filtration - Part 2 : determination of the minimum air volume flow rate of captor hoods and nozzles.
本文件規定了工作在5 GHz至8 GHz頻率范圍內（除5 862 MHz和5 890 MHz外）的集成波束成形相控陣天線無線電發射機和接收機的技術特性和測量方法，用于船舶之間以及船舶與陸地站之間的寬帶通信鏈路。 本文件旨在提供可能在考慮使用許可或其他權限時有用的參數。 注：在5 862 MHz和5
Maritime mobile broadband communication links; Radio transmitters and receivers employing integrated beamforming phased array antennas operating in the 5 GHz to 8 GHz frequency range
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 1: Determination of fume emission rate during arc welding and collection of fume for analysis
DIN EN ISO 15012-2:2008 焊接和相關工藝的衛生和安全.空氣過濾用設備的要求、試驗和標記.第2部分:采集罩和噴嘴的最小空氣體積流率的測定
This part of ISO 15012 specifies a method for establishing the minimum air volume flow rate required for captor hoods and nozzles to effectively
Health and safety in welding and allied processes - Requirements, testing and marking of equipment for air filtration - Part 2: Determination of the minimum air volume flow rate of captor hoods and nozzles (ISO 15012-2:2008); English version of DIN EN ISO
This document specifies a process for environmental performance evaluation of activities executed by a manufacturing system based on the general
Automation systems and integration - Evaluating energy efficiency and other factors of manufacturing systems that influence the environment - Part 2: Environmental performance evaluation process (ISO 20140-2:2018, IDT)
This part of ISO 15011 defines a laboratory method for measuring the emission rate of fume from arc welding.It also defines a method of collecting
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 1: Determination of fume emission rate during arc welding and collection of fume for analysis
This part of ISO 15012 specifies a method for establishing the minimum air volume flow rate required for captor hoods and nozzles to effectively
Health and safety in welding and allied processes - Requirements, testing and marking of equipment for air filtration - Part 2: Determination of the minimum air volume flow rate of captor hoods and nozzles
