共找到 150 條與 邵爾A型硬度計 相關的標準，共 10 頁
GASKET, CORK/NEOPRENE-40 DUROMETER"A" HARDNESS ***TO BE USED WITH FORD WSS-M99P1111-A***
ELASTOMER ?THERMOPLASTIC - STYRENIC TYPE SEBS, 75 SHORE A
本規范涵蓋了用于航空和航天應用的模壓環、壓縮密封件、O型圈繩和模壓墊片的硅橡膠。對于板材、帶材、管材、擠出件和模壓形狀，請使用AMS3307規范。 1.2 應用 該材料的典型使用溫度范圍為-67至+392°F（-55至+200°C）。材料的使用溫度范圍是一個通用范圍，但特定流體和設計要求可能會修改此
Rubber: Silicone [VMQ] Non-Oil Resistant Low Compression Set, 65 - 75 Type A Hardness
THERMOPLASTIC POLYURETHANE ELASTOMER (TPU) MOLDING COMPOUND, INTERIOR, MIC, 90 DUROMETER A HARDNESS ***TO BE USED WITH FORD WSS-M99P1111-A***
POLYVINYL CHLORIDE (PVC), FLEXIBLE, 85 A DUROMETER HARDNESS, INTERIOR **TO BE USED WITH FORD WSS-M99P1111-A*** (Shown on WSB-M4D871-A1)
Hardmetal－Rockwell hardness test(scale A)－Part 1：Test method
Thermoplastic Elastomer - Styrenic Block Copolymer, Shore A80, Interior/Exterior, Integrally Colored
Hardmetals - Rockwell test (scales A and 45N) - Calibration of reference blocks out of hardmetals to be used for the verification and calibration of hardness testing machines
本規范涵蓋了用于航空和航天應用的高溫、壓縮變形和耐液體氟碳（FKM）彈性體，形式包括模壓環、壓縮密封件、O型圈繩和模壓墊片。該材料對多種燃氣渦輪發動機油具有抵抗力，包括高熱穩定性（HTS）油、燃料和液壓流體，但使用不僅限于此類應用。該材料的典型使用溫度范圍為-65至+400°F（-54至+204°C
Rubber: Fluorocarbon Elastomer (FKM) Aircraft Engine Oil, Fuel and Hydraulic Fluid Resistant 70 to 80 Shore Type A Hardness Low Temperature Sealing Tg -47 °F (-43.9 °C) for Elastomeric Seals in Aircraft Engine, Fuel and Hydraulic Systems
THERMOPLASTIC ELASTOMER (TES) STYRENE BLOCK COPOLYMER 45 DUROMETER A HARDNESS, INTERIOR ***TO BE USED WITH FORD WSS-M99P1111-A***
Thermoplastic Elastomer - Styrene Block Copolymer, Shore A73, Interior, Non-UV Stabilized
Shore A and Shore D hardness testing of rubber
POLYURETHANE ELASTOMER, SHORE HARDNESS A 85
Form This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet@ strip@ tubing
Elastomer: Fluorosilicone Rubber (FVMQ) Fuel and Oil Resistant 75 - 85 Durometer Type “A” Hardness For Products in Fuel Systems/Lubricating Oils
Schválení ST SEV 2003-79 doporu?ilo federální ministerstvo hutnictví a tě?kého strojírenství. Zpracovatel a oborové normaliza?ní st?edisko
Testing of sintered carbides. Rockwell hardness test (scale A)
