共找到 150 條與 邵爾A型硬度計 相關的標準，共 10 頁
Rubber, vulcanized or thermoplastic. Determination of indentation hardness. Part 1. Durometer method of measurement (Shore hardness)
Diese Internationale Norm befasst sich mit der Prüfung von Typ-A-Shore- und Typ-D-Shore-Durometern, die für die Durchführung von H?rteprüfungen, wie
Plastics and ebonite - Verification of Shore durometers
Zpracovatel a oborové normaliza?ní st?edisko: Technick? a zku?ební ústav stavební, Praha - Ing. Vlastimil < Grabmiiller Pracovník ??adu pro
Testing of caulking compounds for building purposes. Indentation hardness of elastomeric sealants by means of durometer by Shore a
本規程適用于A型巴氏硬度計的首次檢定、后續檢定和使用中檢查
Type A Barcol Hardness Testers
Zpracovatel: V?zkumn? ústav gumárenské a plastiká?ské technologie Gottwaldov — Miroslav Tichava, dipl. technik Oborové normaliza?ní st?edisko: V
Determination oí frardness o? vulcanized rubber by the meihod Shore D
La presente norma è la versione ufficiale in lingua italiana della norma europea EN ISO 868 (edizione novembre 1997). La norma descrive un metodo
Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness).
本規范涵蓋了一種硅橡膠（VMQ）彈性體，可用于制造片材、條材、管材、擠出件和模壓形狀的產品。對于航空和航天應用的模壓環、壓縮密封件、O型圈繩和模壓到位墊圈，請使用AMS7XXX規范。 1.2 應用 該材料類型具有耐候性和耐臭氧性，并且特別配制成低壓縮變形，但用途不限于此類應用。該材料類型的典型使用
Elastomer: Rubber, Silicone (VMQ) Non-Oil-Resistant Low Compression Set 65 - 75 Shore A Hardness
Revision b-12/1987 Czech National Standard 62 1431*/1198-78 Rubber Test Hardness Determination Shore A
Thermoplastic Elastomer - Polyolefinic, Shore D40
1.1 This test method describes twelve types of rubber hardness measurement devices known as durometers: Types A, B, C, D, DO, E, M, O, OO, OOO
Standard Test Method for Rubber Property8212;Durometer Hardness
Describes the measurements of the appropriate hardness where only medium precision is required. The method and apparatus used are essentially those
Rubber-covered rollers; Determination of apparent hardness; Part 2 : Shore-type durometer method
La norma specifica un metodo per la determinazione della durezza di penetrazione della gomma vulcanizzata o termoplastica utilizzando durometri con
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1: Durometer method (Shore hardness)
本文件描述了硫化橡膠或熱塑性橡膠包覆輥表觀硬度(以邵氏硬度表示)的測定方法,該方法只適用于中等精度要求的測量。該方法及所用儀器基本如ISO48 4 所描述,測量是在經過處理的膠輥的曲面上進行,而不是在平面試片上進行的。 本文件規定了邵氏A型和D型儀器,后者用于測量高硬度膠輥。 注:對于某些膠輥,表面
Rubber,vulcanized or thermoplastic—Determination of hardness—Part 7:Apparent hardness of rubber-covered rollers by Shore-type durometer method
La norma specifica un metodo per la determinazione della durezza di penetrazione della gomma vulcanizzata o termoplastica utilizzando durometri con
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 1: Durometer method (Shore hardness)
Elastomer: Fluorosilicone Rubber (FVMQ) Fuel and Oil Resistant, High Strength 45 – 55 Shore A Hardness For Products in Fuel Systems / Lubricating Oils
