共找到 150 條與 校準模式 相關的標準，共 10 頁
本規范適用于多參數生理模擬儀的校準
Calibration Specification for Multiparameter Physiological Simulators
Calibration Specification for Infrared Thermometers for Measurement of Human Temperature
本規范規定了無線信道模擬器的校準項目、方法及數據處理，適用于無線信道模擬器的校準
Calibration Specification for Wireless Channel Emulator
本規范適用于電噴霧-飛行時間質譜儀和基質輔助激光誘導解吸飛行時間質譜儀的校準，其他類型的飛行時間質譜儀可參照本規范進行校準
Calibration Specification for Time-of-Flight Mass Spectrometers
本規范適用于常壓的混合式油罐測量系統(簡稱HTMS)的校準
Calibration Specification for Hybrid Tank Measurement System
Most site-specific ground-water flow models must be calibrated prior to use in predictions. In these cases, calibration is a necessary
Standard Guide for Calibrating a Ground-Water Flow Model Application
Most site-specific ground-water flow models must be calibrated prior to use in predictions. In these cases, calibration is a necessary
Standard Guide for Calibrating a Ground-Water Flow Model Application
本規范適用于新制造、使用中及修理后，工作頻率范圍在O.3MHz~5.OMHz的單極、雙極醫用高頻電刀的校準。本規范不適用于單極工作模式下最大輸出功率小于50W的醫用高頻電刀的校準，也不適用于雙極工作模式下的齒科、婦科及皮膚科等專用高頻電刀的校準
Calibratior Specification for Electrosurgical Generator
Because of the complexity of water systems, the wide variety of problems that can be addressed by models and the cumulative effect of approximations
Standards for Model Calibration
檢測實驗室的質量保證，特別是在實驗室認可時（參看GB/T 15481），質量保證的重點需要周密考慮其測量和分析結果的準確度問題，并確保考慮了建立證明準確度所需的原則。 尤其值得注意與化學分析和材料檢測有關的參數的校準，因為主要誤差是由忽略或不顧及也適用于這些領域的計量學基本原則而
Directives for the work of reference materials(9)-Calibration in analytical chemistry and use of certified reference materials
本文件規定了醫學校準實驗室運行參考測量程序的能力要求。 本文件以GB/T27025—2019 的要求為規范性參考,列出了校準實驗室充分執行任務的附加要求。 本文件與GB/T27025—2019 條款的關系總結于附錄A中。 本文件不包括以名義標度或序數標度報告結果的特性的測量。 本文件不適用于醫學
Laboratory medicine—Requirements for the competence of calibration laboratories using reference measurement procedures
Calibration specification for large modulus mechanical hob inspector
Residential Vertical Geothermal Heat Pump System Models: Calibration to Data
1.1 This test method describes the temperature calibration or conformance of rheometers. The applicable temperature range is 0 °C to 80 °C however
Standard Test Method for Temperature Calibration of Rheometers in Isothermal Mode
本規范中規定的校準方法適用于溫度范圍-80 ℃— +1 300 ℃的干體式溫度校準器(以下簡稱干體爐)的校準。校準溫度不應超出干體爐生產廠家給出的溫度范圍
Calibration Guideline of the Temperature Block Calibrators
